Interior / Exterior Visual TechThis section contains discussion related to visual modifications of the Toyota FJ Cruiser. Some items might include dash kits, roof rack modifications and other visual modifications.
all right guys..is there a trick to removing the break light/back up light lense cover? i gust recieved my replacement bulbs, and now time to pull cover off..is there a trick? already chipped corner of cover and am not wanting to damage it any further. im sure there is a trick to it, just need someone to tell me what it is
__________________ 6" fabtech, 5 pro comp 35x12.5x17ext at's, dirt logic 2.5coilover
2 kicker solo 12's, boston acq tweet dash
boston acq 6.5 door,boston acq 3.25 pilar
boston acq 6.5 back wall, pioner 6800 dvd/cd 7" dd
kicker 1000 watt amp, american racing thugs
arb full roof rack, garmin gps, trd cai
throttle body spacer,flow master exhaust
spider trax spacers, 9k hid's
manik rear light gurards, unichip programmer,
swiss army overhead light, hi lift jack,
arb lift/shovle mount,
ellis precision handles,
custome rocktek sliders
Location: Oh mommy I ain't no commie I'm just doing what I can to live the good all American...Way
Posts: 2,100
Re: Reverse Light Replacement
I believe you have to go from inside the vehicle, behind the cover panels.. Ron
QUOTE=ajstoy;945445]all right guys..is there a trick to removing the break light/back up light lense cover? i gust recieved my replacement bulbs, and now time to pull cover off..is there a trick? already chipped corner of cover and am not wanting to damage it any further. im sure there is a trick to it, just need someone to tell me what it is[/quote]
__________________
08 SS, SS valve stem caps and exhaust tip
Rapper standing on the corner, wrappers flying in the wind... And in my quite reflection, I wonder why..
Location: Oh mommy I ain't no commie I'm just doing what I can to live the good all American...Way
Posts: 2,100
Re: Reverse Light Replacement
NP.. I read that here somewhere.. Ron
Quote:
ajstoy previously said:
that would make sense..nothing good, is simple! thnax ron
__________________
08 SS, SS valve stem caps and exhaust tip
Rapper standing on the corner, wrappers flying in the wind... And in my quite reflection, I wonder why..
If your just replacing the bulbs then go thru the small panel (on the inside) right behind the tail light. You don't need to remove the len itself.
EDIT: if you do want to remove the len, there are two screw nuts in the small panel you will need to take off, then the third is either located in the stock jack compartment and the other is behind the stock sub compartment.
all right guys..is there a trick to removing the break light/back up light lense cover? i gust recieved my replacement bulbs, and now time to pull cover off..is there a trick? already chipped corner of cover and am not wanting to damage it any further. im sure there is a trick to it, just need someone to tell me what it is
There are small access panels on each side used for access to the bulbs and sockets. If you have a sub-woofer you must remove it to access the passenger side panel. Push and twist left to remove the light socket and bulb. Remove the bulbs by pulling gently. Install the new bulbs, push and turn right to re-install the sockets.
__________________
TLCA#16768
33' BFG MUD's, Icon Front Coil Overs, OME Rear Shocks and Coils. ARB Bumper, Warn 9500XD winch, MAF Sliders & Skid Plates, Gobi Ranger Rack w/ PIAA Lights ft, rr, sd, w/Gobi Hi Lift, axe and shovel Mounts, dust lights. Dirty Parts Dual Battery System, Cobra 75 WX ST CB, Extreme Hi Lift Jack, Power Tank 10 lbs. CO2 System, All Pro HD LCA's, Custom Rear Drawers. Custom electrical.
6" fabtech, 5 pro comp 35x12.5x17ext at's, dirt logic 2.5coilover
Linear Mode
